CNC Corrugated Carton Cutting Machine 1600×2500 | OEM Available

Built by Our Own Factory Floor — Every RT-D2516/RT-S2516 frame is machined, assembled, and tested under the same roof in Jinan, so the team answering your technical call is the one that bolted the linear guides down.

Technical Specifications

Application Suitability

Why Board Grade Matters More Than Table Size

We confirm your actual flute profile before we quote the knife configuration.

A buyer once sent us a spec sheet asking for a 1600×2500 mm table, assuming any CNC corrugated carton cutting machine manufacturer could handle their workload. When the machine arrived, they were running double-wall reinforced corrugated at 300 GSM liner weight — a grade our standard oscillating knife was never set up to shear through at production speed. The knife stalled mid-cut, edges frayed, and the vacuum table could not hold the warped sheet flat [NEED_CITE: corrugated flute profiles and GSM impact on cutting force]. That single mismatch cost them an entire week of sample approvals.

Knife Head Configuration for Corrugated Substrates

The RT-D2516 and RT-S2516 use a Swiss imported multifunctional head with vibration full-cut and half-cut modes. Vibration cutting matters on corrugated board because the flutes create alternating hard and soft layers; a static drag knife tears the liner at each flute peak. The oscillating action shears cleanly through both liner and medium at cutting speeds between 200 and 800 mm/s, depending on board density. For creasing, the half-cut mode scores the top liner without penetrating the bottom, giving a fold line that holds without cracking the printed surface.

Vacuum Zoning Across the Full 1600×2500 Bed

The aluminum alloy honeycomb platform paired with a 7.5 kW vacuum pump provides uniform hold-down across the entire working area. On nested carton layouts, small offcuts and narrow side panels tend to lift when the vacuum zone is too broad, pulling the sheet and throwing off crease registration. The honeycomb structure distributes suction evenly so that even a 40 mm wide tab stays pinned while the knife finishes its pass [NEED_CITE: vacuum hold-down requirements for flatbed digital cutting].

Reading the Spec Sheet Before You Sign

Repeated accuracy of ≤0.1 mm comes from Taiwan Hiwin linear rails and Delta servo motors driving synchronous belts and ball screws. On a 2500 mm stroke, thermal expansion and belt stretch can drift registration by tenths of a millimeter over a long shift. The Hiwin rail and servo combination keeps the carriage square to the bed, so crease lines stay within tolerance whether you are cutting your first sample at 8 AM or your fiftieth production sheet after lunch. Translational velocity reaches 1200 mm/s between cuts, reducing non-cutting travel time on complex nested layouts.

The Cost of a Wrong Tool Head Choice

When a machine is sold on working area alone, the buyer often discovers mid-production that the knife cannot handle their material thickness. Ragged edges on double-wall board mean rejected samples and re-cut orders. On sticker contour jobs, insufficient vacuum causes vinyl lift and misregistered kiss-cuts, wasting printed stock [NEED_CITE: tool head selection for oscillating knife cutting machines].

Why Buyers Source This Machine Here

In-house design and production covering knife cutting technology means the tool head and table configuration are specified per your material and production volume, not forced into a one-size catalog. CCD camera positioning is available for printed contour work where registration marks must be tracked at cutting speed. Software compatibility with your existing file formats is confirmed before order, not discovered after delivery. Voltage, control language, and plug type are matched to your facility spec sheet before the crate leaves Jinan. Sample cutting on your own corrugated board grade is done and documented before you commit.

Documentation & Verification

• Machine specification sheet listing knife head and table configuration matched to your board grade
• Electrical schematic with 380V ±10% voltage confirmation and circuit protection details
• Sample cutting report run on your supplied corrugated board before shipment approval
• Software licence documentation and file format compatibility note for your CAD workflow
• CE declaration documentation for applicable markets (basis not stated in source)
• Factory test record with dimensional accuracy and cutting speed validation on your material

Installation, Commissioning & Support

• Requires level concrete floor supporting 3450×2300×1250 mm footprint and 9 kW plus 7.5 kW vacuum load
• Dedicated 380V ±10% three-phase circuit with correct plug type confirmed before dispatch
• Fully assembled configuration to be confirmed; on-site leveling and belt tension check required
• First-run parameter setting for your specific board flute profile and cutting speed calibration
• Operator training on carton nesting software, HP-GL file import, and tool head changeover procedure
• Spare oscillating knife blades and wear parts list provided with initial supply kit

What We Need From You to Quote Accurately

Send us your actual corrugated board samples — the grades and flute profiles you run most often — along with a DXF or PLT file of your typical carton layout. Tell us your facility voltage, frequency, and preferred control panel language. If you have existing nesting software or a CAD system upstream, share a sample export file so we confirm import compatibility before build.

Frequently Asked Questions

Q: How do I verify the machine can cut my specific corrugated board before ordering?
A: Send us physical samples of your board grade and flute profile. We run sample cuts on our factory floor, document edge quality, cutting speed, and vacuum hold-down performance, and send you the cutting report with photos before you confirm the order.

Q: Can the voltage and control language be matched to my country?
A: Yes. The standard 380V ±10% configuration is adjusted for your local supply, and the control panel language is set from available options including English, Russian, Italian, and Chinese, with additional languages customizable on request.

Q: When should I use vibration full-cut versus half-cut on corrugated board?
A: Vibration full-cut is used for through-cutting the entire board thickness to release the carton blank. Half-cut scores only the top liner for fold lines. The correct choice depends on your board grade and whether the fold line carries printed graphics.

Q: Will the vacuum table hold small carton parts during nested cutting?
A: The honeycomb platform with 7.5 kW pump distributes suction across the 1600×2500 mm bed. For very narrow parts under 50 mm wide, we review your nesting layout and confirm vacuum zoning adequacy before build.

Q: Is the nesting software compatible with my existing CAD file formats?
A: The included carton nesting software supports multiple file format imports and works with HP-GL compatible output. Share a sample export file from your current CAD system so we verify full compatibility before shipment.