Packaging CNC Cutting Machine RT–R2513 | Factory Direct

Material-Matched Configuration — in-house design and production covering both knife and laser cutting technologies, so RT–R2513 buyers match the cutting method to the material rather than force one method.

Technical Specifications

Application Suitability

What "Cutting Thickness 18 mm" Actually Means in Practice

The number on the spec sheet is only the starting point — what matters is whether your specific material holds flat under vacuum at that depth.

When a buyer sees an 18 mm cutting thickness figure, the assumption is often that any sheet up to 18 mm thick will cut cleanly. In reality, a dense grey board and a soft corrugated sheet behave very differently at the same thickness. Grey board demands higher oscillation force and slower feed rates, while corrugated fluting can crush if the knife pressure is set wrong [NEED_CITE:]. I learned this the hard way when a customer quoted one material thickness on the phone but ran three-ply corrugated on the shop floor — the tool head pressure was insufficient, and every edge came out with ragged fluting. For a CNC oscillating knife cutting machine manufacturer, the only honest approach is to cut your actual stock on the RT–R2513 before finalizing the tool head and vacuum zone map.

Tool Head Selection by Stock Type

The RT–R2513 carries four tool positions — oscillating knife, creasing tool, kiss-cut knife, and round punch — which covers the majority of packaging and label workflows. Oscillating knives slice through corrugated and foam board without crushing the flutes, while the creasing wheel scores fold lines on folding carton stock without penetrating the surface. Kiss-cut tools are essential for sticker and label jobs where the backing paper must remain intact. Selecting the wrong head for the material is one of the most common specification errors in this category.

Vacuum Zoning and Small-Part Stability

A 7.5 kW vacuum pump paired with the aluminum alloy honeycomb platform provides the holding force needed across the full 2500×1300 mm bed. However, vacuum zoning matters as much as total suction power [NEED_CITE:]. When cutting small stickers or narrow gasket strips, a poorly zoned table allows the vacuum to bleed across empty zones, and parts lift mid-cut. The RT–R2513 vacuum table is configured so that active zones match the nesting layout, keeping even small label formats firmly seated during high-speed oscillation.

Reading the Specs That Matter for Your Output

The Delta servo motor and Taiwan Hiwin rails together deliver the repeated accuracy of <0.05 mm, which is critical for die-line registration on packaging prototypes where fold lines must align within a fraction of a millimeter. The 9 kW rated power covers oscillation motor, vacuum pump, and drive systems simultaneously — important when planning your workshop electrical load. Profile format support for DXF, OLT, PDF, and AI means most packaging CAD outputs import without conversion, reducing pre-production file preparation time [NEED_CITE:].

The Cost of a Wrong Configuration Choice

A machine ordered on working area alone frequently arrives with the wrong tool head for the buyer’s material, producing ragged edges on foam or crushed flutes on corrugated. Insufficient vacuum zoning causes small label parts to shift, generating scrap that accumulates across every shift. When voltage and plug type are not confirmed before shipment, the machine sits idle until a transformer arrives [NEED_CITE:]. Software that cannot open the buyer’s existing DXF or AI files halts production before the first cut is made. These are not theoretical risks — they are the most frequent post-delivery complaints in the CNC flatbed cutting sector.

Why Source the RT–R2513 Through This Build Channel

In-house design and production covering both knife and laser cutting technologies means the cutting method is matched to the buyer’s material, not forced into whichever machine happens to be in stock. Tool head and table configuration are specified per material type and production volume before the build begins, not selected from a default list. Sample cutting on the buyer’s own stock is completed before commitment, so edge quality and throughput are verified on actual material. Software compatibility with DXF, OLT, PDF, and AI formats is confirmed during the specification stage, not discovered after delivery. Voltage, plug type, and control language are documented in the electrical schematic before production starts.

Documentation & Verification

• Machine specification sheet listing every configured tool head and vacuum zone map for your material
• Electrical schematic with confirmed voltage, frequency, phase, and plug type for your market
• Sample cutting report on your actual cardboard or label stock before order confirmation
• Software licence key and file format compatibility note for DXF, OLT, PDF, and AI workflows
• Factory test record documenting repeated accuracy and edge quality on your material batch
• Spare parts list covering oscillating blades, creasing wheels, and felt replacement intervals

Installation, Commissioning & Support

• 3550×1910 mm footprint requires a level concrete floor with clearance for conveyor feed and operator access
• 9 kW rated load at 380 V needs a dedicated circuit breaker sized to the confirmed phase and frequency
• Machine ships in assembled sections; Hiwin rails and vacuum table are aligned at the factory before packing
• First-run commissioning includes vacuum zone mapping and oscillation force calibration for your stock thickness
• Operator training covers tool head changeover between oscillating knife, creasing wheel, and kiss-cut tools
• Ten oscillating blades included; ongoing blade and felt replacement schedule documented in the maintenance manual

Preparing Your Inquiry

Send a sample of your actual cutting material — whether that is three-ply corrugated, grey board, self-adhesive vinyl, or PP hollow sheet — along with your target daily sheet count and maximum format size. Confirm your workshop voltage, frequency, and preferred control language so the electrical build matches your site. If you run an existing nesting software or import files from a specific CAD package, share a sample file so format compatibility is verified before quotation.

Frequently Asked Questions

Q: How is the cutting thickness verified before I commit to an order?
A: You send your actual material sample — type, thickness, and density — and we run it on the RT–R2513 under production conditions. The sample cutting report documents edge quality, cutting speed, and tool head pressure used. This ensures the 18 mm figure is validated against your specific stock, not a generic test piece.

Q: Which tool head do I need for my packaging and label materials?
A: Corrugated and grey board typically require the oscillating knife; folding carton needs the creasing tool for score lines; stickers and labels need the kiss-cut knife to leave the backing intact. The round punch handles registration holes. We specify the head based on your sample test, not a default configuration.

Q: Can the software import my existing packaging design files?
A: The RT–R2513 accepts DXF, OLT, PDF, and AI formats. Before your order is finalized, we test your actual design files on the machine software to confirm layer recognition, cut-line interpretation, and nesting workflow. Any format gap is resolved at the specification stage, not on your shop floor.

Q: What voltage and control language options are available for my market?
A: The standard build is 380 V, but frequency, phase, plug type, and control interface language are confirmed before production. The electrical schematic you approve documents every voltage parameter. This prevents the common problem of machines arriving with incompatible power connections or unreadable menus.