Paper Board Die Cutting Machine 100m/min 11kW | OEM Available

In-House Engineering Control — Every weld seam on the RT-D2516/RT-S2516 frame and every Delta servo calibration trace back to our Jinan assembly floor, giving distributors full visibility into build provenance.

Technical Specifications

Application Suitability

Why the Voltage Question Must Come Before the Purchase Order

A cutting table wired for the wrong frequency loses its vacuum hold before the blade even touches the board.

I watched a distributor in Southeast Asia unpack a digital cutter that was specified only by working area. The local grid ran 220V/60Hz, but the machine left the factory on 380V/50Hz. The 7.5 kW vacuum pump could not pull rated suction, and small corrugated pieces lifted off the table mid-cut. That entire container sat idle while transformers and motor rewinds were arranged locally [NEED_CITE: voltage and frequency standards by export market]. When sourcing a CNC oscillating knife cutting machine manufacturer, the first document exchanged should be the electrical schematic matched to the destination grid, not the brochure.

Frame Construction and Long-Term Geometric Stability

The RT-D2516/RT-S2516 chassis is built from thick-wall square seamless steel tube, welded in-house and passed through a high-temperature stress-relief cycle. This treatment releases internal welding tension so the frame does not warp after months of vibration from the oscillating knife head. For a distributor, that means the machine arrives with the same geometric alignment it had on the first day, and repeat orders stay dimensionally consistent without field re-calibration. The 1600 × 2500 mm working area is sized to handle full sheets of corrugated board common in carton sample rooms.

Motion Components and Positional Repeatability

Taiwan Hiwin linear guides paired with Delta digital servo motors drive every axis. The repeated accuracy stays within 0.1 mm, which matters when a packaging designer nests dozens of small box blanks on a single sheet — any drift accumulates across the cut path and ruins the entire nest. The synchronous belt and ball screw combination keeps the tool head locked on trajectory even at translational speeds reaching 1200 mm/s. As a CNC oscillating knife cutting machine manufacturer, Realtop selects these motion parts because they are globally serviceable; a distributor can source replacement bearings or rails without depending on a single supply chain [NEED_CITE: Hiwin and Delta global service network].

Reading the Specs That Actually Matter for Carton Work

The Swiss oscillating knife head handles full cut, half cut, and cursor registration on the same tool mount, so an operator can score a fold line and cut the outer contour without a tool change. The 7.5 kW vacuum pump is paired with an aluminum honeycomb table — the honeycomb cells allow airflow across the entire surface, but zoning the vacuum into sections means small sticker pieces hold flat without needing full-table suction and burning unnecessary energy. The professional carton software imports standard file formats and lets the operator nest jobs before sending them to the controller. Cutting speed ranges from 200 to 800 mm/s depending on material density; high-density grey board will always sit at the lower end of that range, while single-face corrugated runs near the top.

The Hidden Cost of Skipping a Material Trial

I once worked with a carton sample shop that specified a machine purely on maximum speed. They ran dense grey board for premium gift boxes, and the blade could not penetrate cleanly at the quoted rate. They had to cut at half speed to get acceptable edges, which erased the throughput advantage they thought they were buying. Without a trial on the buyer’s actual stock, a cutting speed figure on a spec sheet is just a number [NEED_CITE: material density effect on oscillating knife cutting speed]. The RT-D2516/RT-S2516 supports sample cutting on the buyer’s own material before the contract is signed, so the real production rate is confirmed — not assumed.

Why Distributors Source This Platform Here

Realtop runs in-house design and final assembly for both knife and laser platforms, so a distributor evaluating a CNC oscillating knife cutting machine manufacturer can trace every sub-assembly to a single factory floor rather than a network of outsourced workshops. Voltage, plug type, and software language are confirmed line-by-line before production starts, eliminating the costly field modifications that eat into dealer margins. The OEM configuration range covers working area, tool head combination, and conveyor options, allowing dealers to stock variants suited to different regional markets. Factory test records are generated on the buyer’s chosen material and shared before crating. Spare parts lists ship with every machine, and the one-year warranty carries lifetime technical support backed by the same engineering team that built the unit.

Documentation & Verification

• Machine specification sheet matched to confirmed RT-D2516/RT-S2516 configuration
• Electrical schematic and voltage confirmation signed before production
• Tool head and vacuum table configuration list attached to packing documents
• Sample cutting report produced on buyer’s own board stock before dispatch
• Factory test record with dimensional accuracy measurements documented
• CE declaration included where applicable to destination market

Installation, Commissioning & Support

• Requires level concrete floor to support 3450 × 2300 mm footprint and dynamic vibration load
• Dedicated 380V circuit with adequate breaker rating for 9 kW total draw plus vacuum pump
• Machine ships fully assembled; only conveyor and external vacuum hose connections needed on site
• First-run parameter tuning performed on buyer’s material to lock cutting speed and knife depth
• Operator training covers software nesting, tool head changeover, and vacuum zone configuration
• Wear parts list includes felt belt, oscillating knife blades, and vacuum seals stocked for rapid dispatch

What to Include in Your Inquiry

Send your material type, sheet dimensions, typical board thickness, and daily sample volume so the tool head and vacuum configuration can be matched before quoting. Confirm your workshop voltage and frequency, and let us know the preferred control language. If you want sample cuts on your own stock, ship a few sheets and we will return cut pieces with a parameter report.

Frequently Asked Questions

Q: Can the working area and tool head be customized for OEM orders?
A: Yes. The RT-D2516/RT-S2516 platform supports custom table sizes, multiple tool head combinations including oscillating knife, drag knife, creasing wheel, and pen, as well as CCD camera integration. Voltage, plug standard, and software language are all configurable. Each OEM configuration is documented in the specification sheet before production begins so the distributor receives exactly the machine that was agreed upon.

Q: How do we arrange a factory visit and live machine trial?
A: Buyers and distributors are welcome to visit the Jinan assembly floor. We schedule a production slot on a machine matching your configuration, run your material through the full cut cycle, and document the results on site. If travel is not possible, we conduct the trial in-house and share video footage along with cut samples and the test parameter record.

Q: What does the dealer pricing structure look like for repeat orders?
A: Pricing is structured around order volume and configuration complexity. Distributors placing repeat or batch orders receive tiered pricing discussed during the initial partnership conversation. Lead times are confirmed per order based on current production scheduling, and each unit undergoes the same factory test protocol regardless of order size.

Q: Are spare parts readily available after the warranty period?
A: Common wear items such as oscillating knife blades, felt belts, and vacuum seals are kept in stock and can be dispatched on short notice. The spare parts list shipped with each RT-D2516/RT-S2516 identifies every consumable and its part number. Lifetime technical support means the engineering team remains available for troubleshooting long after the first year.

Q: How is the machine packed and what are typical shipping lead times?
A: The machine ships fully assembled in a reinforced wooden crate suited to ocean freight. Packing photographs are taken before the crate is sealed and shared with the buyer. Typical multi-week lead times apply from order confirmation to dispatch, depending on configuration complexity and current production queue.